Thank you for correcting the text in this article. Your corrections improve Papers Past searches for everyone. See the latest corrections.

This article contains searchable text which was automatically generated and may contain errors. Join the community and correct any errors you spot to help us improve Papers Past.

Article image
Article image
Article image
Article image
Article image
Article image
Article image
Article image
Article image
Article image
Article image
Article image
Article image
Article image

Can Be Made by Anyone Having a Little Ingenuity.

■ In reply to a request for directions 'for making a sod cutter, I offer the following, which is very easy to construct N by anyone having 1 ordinary ability in the use of tools end who may have use for such an article as a sod cutter. It is for use with a horsey"eiinid will cut sod art. a very rapid rate, and will cut of a uniform thickness and width. By using a spade that is sharp to follow and cut out the lengths, it is" easy to get any,, sized piece that may be desirable to, handle.

To construct, it; procure a piece ofpine or: oak two inches thick by six'

inches wide and 1 seven- feet long.. Cut in the center and shape one end of each piece like Fig. I.': For the top use a piece of pine two inches thick, 14 inches /wide and three feet long. Spike or fasten • the top board firmly to the side pieces or runners as though making a sled, as in Fig. 4, It will-r equire .two steel cutters, about eight inches long •and firm enough, to be substantial, like FigC S. One steel cutter- (3), thebottorii to be flat 4nd about iy z inches wide, the •length of which, must be width of sled, but which naust be fastened to the sled

on an angle so that the knife or cutt-er ■ which is fastened upright in front will be in .'vdyance of .the^ther..' This cutter ;must--l^''' # yi*eli^made';;6i- r g^dd :: ste'eli ; Svi+ii^." good stout ivpright- en>3s and well bodted to the sides so it will project belo^Jv the ' bottom of the runners about 2^" incfies,> or whatever thickness is deemed best tp cut the' sod. Have it well sharpened , across the- • width- , Place .the two up-! ; right ;? knives^ • well . sharpened; ft just in advance of the uprighls of the

just in advance of the uprights of the i.riife or cutter, allQwing their points : to project half aarinch below the cutter bar. / Fig.'4 shows the cutter compiete with the bottom up. . Uings ; cari.beiput front and a shortchain attached. to hitch the horse to. v : ' y.

In cuttingl drive straight and stand oii the cutter over the knife. It is, best to^,.cu,t crosswise at each end of the strips and remove it, and there will be less trouble to stacrt it eaSfiTtiine. The whole .expense of su<?.h a cutter ought not. to exceed a dollar, andif well made wilJ? last a» lifetime and be' very easy to lend, but harder. t«o keep trace of.— S. L. Harper^ in Qhio Farmer.> ;

Permanent link to this item

https://paperspast.natlib.govt.nz/newspapers/BH19050110.2.11.1

Bibliographic details

Bruce Herald, Volume XXXXI, Issue 2, 10 January 1905, Page 3

Word Count
438

Can Be Made by Anyone Having a Little Ingenuity. Bruce Herald, Volume XXXXI, Issue 2, 10 January 1905, Page 3

Can Be Made by Anyone Having a Little Ingenuity. Bruce Herald, Volume XXXXI, Issue 2, 10 January 1905, Page 3

Help

Log in or create a Papers Past website account

Use your Papers Past website account to correct newspaper text.

By creating and using this account you agree to our terms of use.

Log in with RealMe®

If you’ve used a RealMe login somewhere else, you can use it here too. If you don’t already have a username and password, just click Log in and you can choose to create one.


Log in again to continue your work

Your session has expired.

Log in again with RealMe®


Alert